Original Autel Diagnostic Tools

Autel MaxiIM IM608 is able to add a remote key for Suzuki Swift Dualjet 2020 success. Key type: 47 chip, frequency 433Mhz type B. Have been programmed remote, let’s go to add the key with Autel IM608. Plug connector into OBD2 port, turn on ignition with working key, press IMMO >> VIN >> Auto detect >> Manual selection >> Other >> Swift IMMO status scan >> BCM(8 digits) >> Add key(guided) Follow the notes to operate: Turn hazard on. Turn ignition on. Press “Start” to perform the function automatically. Step1. Read PIN Step2. PIN verification Step3. Key programming All keys will be erased, prepare all keys to program. Calculate PIN online, press “Yes”. Turn ignition ON or force to ignition ON if all keys lost. It shows a number of keys:1, press “Yes” to learn the next one. Swift off, pull out the first key, turn it on with the next key. It shows 2 keys now, press “No” to finish. Learn keys to success. Test the new key, its remote is fine, and ca...

What is going on, guys? Now I’m gonna program a new ignition key fob for the 2014 Chevrolet Silverado with Autel MaxiIM IM608 key programmer . As you can see, this is the new key to be programmed. Connect AutelIM608 scan tool to OBD2 port of the car, turn on the ignition, then let’s get to start: Press “IMMO”>>“VIN” on the upside bar >> Auto detect >> Accept >> OK (if VIN number was blank, press “Read” to acquire) >> Yes 5.3L(L83) >> Transfer case, two speed, switch activated (NQH) >> Hot functions Auto control dual zone (CJ2) >> Base >> Immo & Keys Add/replace key fobs >> Key fob 1 >> Read the notes carefully, press “Continue” Press “Learn” to start, hold and press the LOCK & UNLOCK buttons together on the key until we hear the beep.  Status “Uncommanded” changed to “learn” on the Autel IM608 scanner . That means the key has been learned successfully. Let me check if the key was programmed... The lock & ...

2019 Chevy Cruze took Canadian cluster out to change faceplate, put back in all needles aligned to ZERO. When I turn the vehicle on everything is perfect all gauges cycle. When i drive the vehicle analog and the digital in the center message screen are OFF. Does anyone have any idea if it needs calibration and if Autel IM608 can calibrate? How to do next? let's read the professional's advice: You can't just swap faceplate. the software needs to be changed as well. You"ll need to replace that cluster and of course you'll have to program it using GM SPS. Don't even think about getting a used one. WILL NOT WORK After reading the above advice, I have a question: cluster dont need to be replaced because i know a speedo place that will program it but off course they dont tell me what they’re using to do the job. Answer: Well. As long you know how to edit hex file than you do not need to replace it. Hold on... Did u really take the KM faceplate off and put on a MPH f...

Have Mercedes E350 W212 2012 without any working keys, this car is from the US. And this is a new key, BE key with 3125MHZ. Let's go to program a new key with Autel IM608 . Tap "IMMO"  Tap "Accept". Tap "Mercedes Benz". Tap "Smart mode".  All keys lost. On vehicle. Confirm vehicle information. Read EIS data. Please insert the blank key into the IR keyhole on the Autel IM608 programmer , and press OK. Firmware upgrading to 100%. Is there a key password? Tap "NO". Then press ok to enter Password Calculation process. Tap "Begin".   Connect the device, OBD cable and OBD connector on the wiring harness in sequence. Connect the IR key simulator (APB102 /APB125) to the programmer. Acquiring data and calculating password. Succeed in computing password.  Password calculation completed! Press OK to return to the ALL key lost data collection process and go to the next step.  Generating key file. Write BE key file: please insert the b...